Shipping rates as low as $1.99

Order by 2PM CST for Same Day Shipping

100% FREE returns

Earn points with every order! Learn More

Search

Need help?

Check out our FAQ.

Search

Correcting Fitting Issues on the X300U-A

One of the most common complaints we hear with the X300U-A  is fitting issues or excessive “wiggle room” when on the gun. Luckily there’s an easy fix for this! If you’re curious about the differences between the X300U-A and the X300U-B models, we have a side by side comparison article that you can read HERE. If you’re missing just one or two pieces, we’re offering to replace some for FREE. Request the parts you need HERE. If you need a complete replacement kit, we have the Surefire Z89 Kits HERE.

First start by removing the 6 screws with the provided wrench. Sometimes fit issues can be resolved just by tightening these ¼-½ a turn so it may be worthwhile to try that first. If that doesn’t fix the issue, just continue on to the next steps.

I prefer to remove the battery door while working on the light. It’s not needed so you can leave it on if you want to. The door just pops on and off.

Your X300U-A should come with several pieces in the package. The Universal Mount (marked “U”, pictured center) is usually pre-installed and works well with most pistols. There is also a Picatinny Mount (marked “P”, pictured left) which can be used on handguns or handguards that have a picatinny rail. There is also the Rail Lock (pictured right) which can be used on nearly everything and will give you the tightest fit. The Rail Lock is also adjustable so you can dial it in to get the perfect amount of tension.

Start by laying the rail lock flat on the desk as shown. Inset the small silver wedge and start to thread the screw in through the side.

Next, lay the assembly down on the body of the light as shown. You’ll notice the screw fits into a slot on the side of the light.

Also in the package are two cross sections marked “P” & “U”. For picatinny rails, use the “P” and for everything else, use the “U”.

You will install this on the front of the light body as shown. You will probably need to slightly raise the rail lock mount assembly installed earlier in order to get it to line up properly.

Here is what it should look like when installed properly.

Next, install the rails with the 6 screws. Make sure not to over tighten so the cross bolt can be moved back and forth. Make sure the rails are oriented in the correct direction as well. Get them snug, but not excessively tight. You’ll notice that one of them has a cutout for the cross bolt.

Once the screws are tightened you can replace the battery door and slide the light onto the rail. When it’s on the gun, slide the cross bolt back over, through the rail slot on the gun  and it will click into place. Now, with the light on the gun, you can tighten the small silver screw on the side. 

Looking at the picture below you can see the tab on the rail lock with the SF logo is flush with the mount. 

By tightening the screw you are forcing that tab upwards which applies pressure on the host firearm or rail. This will help eliminate any play or wiggle with the light.

With the light on the gun, tighten the screw until it’s snug and you’re all set! If you’re mounting this on an AR or other handguard where the battery door won’t be resting against anything, you can use the provided pin to keep the battery door shut.

To remove the light from the gun, start by unscrewing the silver screw on the side. Next, squeeze the tabs on the side to relieve pressure from the crossbolt. Slide the crossbolt our (it won’t come all the way out) and now you can remove the light from the firearm.

If you have any questions or comments, feel free to drop them below. We also carry the full line of Surefire lights. 


SureFire CR123A Lithium Batteries 12 battery pack 123A Battery CR123

Surefire CR123A Batteries


SureFire XT07 Switch For X300U-A/B & XH35/30 Lights

The Surefire XT07 Tape Switch for X300U-A/B lights

*New* Surefire X300U-B 1,000 Lumens LED Weapons Mounted Light X300 Ultra
The Surefire X300U-B 

*New* Surefire X300U-A 1,000 Lumens LED Weapons Mounted Light X300 Ultra
The Surefire X300U-A

28 comments

  1. James W Mahaffey

    When I tighten the light down to where it’s not rattling, the light points up and the gun won’t go into my T1 concealed holster. I have to loosen the light until it flattens out. The problem it that the tension is only on the rear, which forces the light to teeter on the wedge mechanism and makes the light tilt upwards.

    1. I’m having the same issue with a turbo on my M&P. Also at distances over 20 yards, the light shines above my point of aim.

  2. Which model will fit my Sig SP2022 9mm best? Please advise

    Thanks

  3. Have you noticed any holster fitment issues with the Rail Lock system? I would like to switch my X300 between a Polymer and a metal pistol, and was wondering if there were any issues with holsters you’ve tested.

    1. Yes, my TRex kydex don’t fit with the rail lock system. I had to switch back to the paddles, and have a crooked fitment once again. Not sure what to do 🙁

  4. Orenthal Grissom

    Does the x300u-A fit on a Taurus g3c by chance?

    1. Was this ever answered?

Leave a Reply to Marcus Do Cancel reply

Your email address will not be published. Required fields are marked *